SATJEE ExamsAll chapters

Chemistry

Solutions: JEE Main practice questions and key rules

Revise the main rules of Solutions, study 3 worked questions, then test yourself with 10 fresh questions. Every question on SATJEE has full steps and the slip to avoid.

Open the revision cardsTake a chapter test

Key rules

  1. M = moles of solute ÷ litres of solution.
    Watch out: Using millilitres directly instead of converting to litres.
  2. Molarity (M) = moles of solute per litre of solution. Convert mL to L first.
    Watch out: Leaving the volume in mL, or stopping at moles without dividing by the volume.
  3. ppm = (mass of component ÷ total mass) × 10⁶, with both masses in the same unit.
    Watch out: Leaving the component mass in mg while the total is in g, which is off by a factor of 1000.
  4. p = KH x: the higher the KH, the lower the solubility of the gas at a given pressure.
    Watch out: Assuming a larger Henry’s law constant means a more soluble gas (true only for the S = kP form).
  5. Henry’s law: solubility of a gas in a liquid is directly proportional to the gas pressure at constant temperature.
    Watch out: Inverting the pressure ratio.
  6. Positive deviation: weaker A–B attraction. Negative deviation: stronger A–B attraction. Ideal: similar interactions throughout.
    Watch out: Mixing up which kind of deviation goes with stronger or weaker A–B interaction.
  7. Molarity uses litres of solution (needs the density); molality uses kilograms of solvent.
    Watch out: Dividing by the mass of solvent instead of the volume of solution, or ignoring the density.
  8. Mole fraction of a component = its moles ÷ total moles of all components.
    Watch out: Using the mole ratio n₂/n₁, or the mass fraction, in place of the mole fraction.

Worked questions

Question 1

The Henry’s law constants KH (in kbar, for p = KH·x) of four gases P, Q, R and S in water at 298 K are: P = 0.611; Q = 1.67; R = 0.413; S = 40.3. At the same partial pressure and temperature, which gas has the lowest mole-fraction solubility in water?

  1. S
  2. Q
  3. P
  4. R

Answer: A. S

  1. Henry’s law: p = KH x, so x = p/KH. At equal p, a larger KH means a smaller x.
  2. Largest KH is 40.3 kbar, for gas S.
  3. So the answer is S.

Common slip: Assuming a larger Henry’s law constant means a more soluble gas (true only for the S = kP form).

Question 2

A mixture of 1 mol of n-hexane and 4 mol of n-heptane forms an ideal solution. At the temperature of the experiment the vapour pressure of pure n-hexane is 600 mm Hg and that of pure n-heptane is 100 mm Hg. What is the total vapour pressure of the solution?

  1. 500 mm Hg
  2. 200 mm Hg
  3. 700 mm Hg
  4. 1000 mm Hg

Answer: B. 200 mm Hg

  1. x(n-hexane) = 1/5 = 0.2 and x(n-heptane) = 0.8.
  2. p(total) = x(n-hexane)·p°(n-hexane) + x(n-heptane)·p°(n-heptane) = 0.2×600 + 0.8×100 = 200 mm Hg.
  3. So the answer is 200 mm Hg.

Common slip: Using the simple average of the two vapour pressures, which ignores the composition.

Question 3

68.4 g of sucrose (a non-electrolyte, molar mass 342 g/mol) is dissolved in water to make 100 mL of solution at 280 K. Taking R = 0.083 L bar K⁻¹ mol⁻¹, what is the osmotic pressure of the solution?

  1. 93 bar
  2. 46.5 bar
  3. 4.65 bar
  4. 0.0465 bar

Answer: B. 46.5 bar

  1. C = (68.4 ÷ 342) mol ÷ 0.1 L = 2 mol/L.
  2. π = C R T = 2 × 0.083 × 280 = 46.5 bar.
  3. So the answer is 46.5 bar.

Common slip: Using the volume in mL (or the moles instead of the concentration) in C R T.

More Chemistry chapters

Start a free test