SATJEE ExamsAll chapters

Physics

Properties of matter: JEE Main practice questions and key rules

Revise the main rules of Properties of matter, study 3 worked questions, then test yourself with 10 fresh questions. Every question on SATJEE has full steps and the slip to avoid.

Open the revision cardsTake a chapter test

Key rules

  1. mass = density × volume.
    Watch out: Dividing instead of multiplying.
  2. Extension is inversely proportional to Young's modulus.
    Watch out: Not inverting the ratio of moduli.
  3. ΔL = FL/(AY) with A = πd²/4 in m².
    Watch out: Using the diameter in place of the radius for the area.
  4. U = ½FΔL = ½ × stress × strain × volume.
    Watch out: Using the full force times extension (Fx).
  5. F₂ = F₁A₂/A₁ and area goes as radius squared.
    Watch out: Using the ratio of radii instead of the ratio of areas.
  6. P = Pₐ + ρgh (gauge pressure is only ρgh).
    Watch out: Forgetting the atmospheric pressure.
  7. Continuity: Av = constant; area ∝ diameter².
    Watch out: Using the diameter ratio without squaring.
  8. Terminal speed scales as radius squared.
    Watch out: Scaling with the radius (drag) rather than radius squared.

Worked questions

Question 1

Take the surface tension of the soap solution as 0.025 N/m. What is the excess pressure inside a liquid drop (one surface) of radius 2 mm?

  1. 12.5 Pa
  2. 25 Pa
  3. 50 Pa
  4. 100 Pa

Answer: B. 25 Pa

  1. A single liquid–gas surface gives ΔP = 2S/r.
  2. ΔP = 2×0.025/(2×10⁻³)
  3. = 25 Pa.
  4. So the answer is 25 Pa.

Common slip: Using 2S/r for a soap bubble in air (which has two surfaces).

Question 2

Taking atmospheric pressure as 1.01 × 10⁵ Pa and g = 9.8 m/s², find the absolute pressure at a depth of 0.76 m in mercury (density 13600 kg/m³).

  1. 2.02 × 10⁵ Pa
  2. 1.52 × 10⁵ Pa
  3. 1.01 × 10⁵ Pa
  4. 1.11 × 10⁵ Pa

Answer: A. 2.02 × 10⁵ Pa

  1. Absolute pressure P = Pₐ + ρgh.
  2. ρgh = 13600×9.8×0.76 = 1.01 × 10⁵ Pa.
  3. P = 1.01×10⁵ + 1.01 × 10⁵ = 2.02 × 10⁵ Pa.
  4. So the answer is 2.02 × 10⁵ Pa.

Common slip: Forgetting the atmospheric pressure.

Question 3

A steel rod (thermal conductivity 50.2 W m⁻¹ K⁻¹) has cross-section 1 cm² and length 1 m. Its ends are held 50 K apart in temperature. What is the steady rate of heat flow?

  1. 0.126 W
  2. 2510 W
  3. 0.251 W
  4. 1 × 10⁻⁴ W

Answer: C. 0.251 W

  1. H = K A ΔT / L.
  2. A = 1×10⁻⁴ m².
  3. H = 50.2×1×10⁻⁴×50/1 = 0.251 W.
  4. So the answer is 0.251 W.

Common slip: Leaving area in cm².

More Physics chapters

Start a free test