Physics
Units and errors: JEE Main practice questions and key rules
Revise the main rules of Units and errors, study 3 worked questions, then test yourself with 10 fresh questions. Every question on SATJEE has full steps and the slip to avoid.
Open the revision cardsTake a chapter test
Key rules
- Leading zeros never count; trailing zeros count only after a decimal point.
Watch out: Counting leading zeros, or counting trailing zeros of a number such as 4500 that has no decimal point. - Least count of a vernier = value of one main-scale division ÷ number of vernier divisions.
Watch out: Dividing by (N − 1) instead of N. - Least count of a screw gauge = pitch ÷ number of circular divisions.
Watch out: Multiplying instead of dividing, or confusing pitch with least count. - Dimension of a derived quantity = product of the dimensions of the quantities in its defining formula.
Watch out: Putting a power in the numerator instead of the denominator (for example pressure as M L T⁻² instead of M L⁻¹ T⁻²). - For X = A ± B, ΔX = ΔA + ΔB (maximum error).
Watch out: Subtracting the errors when the quantities are subtracted. - Make the constant the subject of the formula, then substitute dimensions.
Watch out: Forgetting that the term inside brackets must have the dimensions of the quantity it is added to. - Principle of homogeneity: all terms of a physical equation have the same dimensions.
Watch out: Checking only one term, or forgetting that a sum needs every term to match. - In multiplication or division the result has as many significant figures as the least precise factor.
Watch out: Keeping all the calculator digits, or using the count of the more precise factor.
Worked questions
Question 1
A screw gauge has a pitch of 0.5 mm and 100 divisions on the circular scale. What is its least count?
- 0.05 mm
- 2.5 × 10⁻³ mm
- 50 mm
- 5 × 10⁻³ mm
Answer: D. 5 × 10⁻³ mm
- Pitch is the distance moved by the screw in one full rotation.
- Least count = pitch ÷ number of circular-scale divisions.
- LC = 0.5 ÷ 100 = 5 × 10⁻³ mm.
- So the answer is 5 × 10⁻³ mm.
Common slip: Multiplying instead of dividing, or confusing pitch with least count.
Question 2
What is the dimensional formula of force? (M, L, T denote mass, length, time.)
- [M L² T⁻¹]
- [L T⁻²]
- [M⁻¹ L³ T⁻²]
- [M L T⁻²]
Answer: D. [M L T⁻²]
- Write force in terms of quantities you know, then replace each by its dimensions.
- Appendix A9 of NCERT lists force as [M L T⁻²].
- So the answer is [M L T⁻²].
Common slip: Putting a power in the numerator instead of the denominator (for example pressure as M L T⁻² instead of M L⁻¹ T⁻²).
Question 3
In Stokes drag F = 6πηav (a is a radius, v a speed), what is the dimensional formula of η?
- [M L⁻¹ T⁻¹]
- [M⁻¹ L T]
- [M² L⁻¹ T⁻²]
- [M T⁻¹]
Answer: A. [M L⁻¹ T⁻¹]
- Both sides of a physical equation, and every term added or subtracted, must have the same dimensions.
- Solve the formula for the constant and substitute the dimensions of each quantity.
- The constant has dimensions [M L⁻¹ T⁻¹].
- So the answer is [M L⁻¹ T⁻¹].
Common slip: Forgetting that the term inside brackets must have the dimensions of the quantity it is added to.
More Physics chapters
Start a free test