SATJEE ExamsAll chapters

Physics

Experimental skills: JEE Main practice questions and key rules

Revise the main rules of Experimental skills, study 3 worked questions, then test yourself with 10 fresh questions. Every question on SATJEE has full steps and the slip to avoid.

Open the revision cardsTake a chapter test

Key rules

  1. Vernier reading = main-scale reading + (coinciding vernier division) × least count.
    Watch out: Multiplying the coinciding division by a main-scale division instead of by the least count.
  2. Slope of a V–I graph gives the resistance, even if the line does not pass through the origin.
    Watch out: Dividing a single V by a single I, or forgetting to convert mA to A.
  3. Zero error is positive if the vernier zero is to the right (coincidence k gives +k·LC) and negative if to the left (−(N−k)·LC). Corrected = observed − zero error.
    Watch out: Treating a leftward zero as +k·LC, or adding the zero error.
  4. Corrected reading = observed − zero error; zero error = (zero reading in divisions) × LC with its sign.
    Watch out: Adding a positive zero error instead of subtracting it.
  5. From a load–extension graph, Y = (slope in N/m) × L / A.
    Watch out: Forgetting to convert mm to m, or leaving out g.
  6. Energy of an oscillator = ½kA², so E ∝ A².
    Watch out: Using amplitude ratio directly instead of its square.
  7. Metre bridge: X = R(100 − l)/l, with l measured from the end next to R.
    Watch out: Interchanging l and (100 − l).
  8. Y = stress/strain = FL/(AΔL) = 4FL/(πd²ΔL); use the corrected diameter, converted to metres.
    Watch out: Using the uncorrected diameter, or using d instead of d² for the area.

Worked questions

Question 1

In a Young's modulus experiment (take g = 9.8 m/s²) a wire of length 1.7 m is loaded. A screw gauge with zero error +0.02 mm gives a mean observed diameter of 0.76 mm. Increasing the load by 1 kg increases the length by 0.75 mm. Find Young's modulus of the wire from this one pair of readings.

  1. 5.16 × 10¹⁰ N/m²
  2. 1.29 × 10¹⁰ N/m²
  3. 3.82 × 10⁷ N/m²
  4. 4.9 × 10¹⁰ N/m²

Answer: A. 5.16 × 10¹⁰ N/m²

  1. Corrected diameter d = 0.76 − (+0.02) = 0.74 mm.
  2. Y = (F/A)/(ΔL/L) = 4 F L / (π d² ΔL), with F = Mg.
  3. F = 9.8 N, A = π d²/4 = 4.3 × 10⁻⁷ m², ΔL = 0.75×10⁻³ m.
  4. Y = 5.16 × 10¹⁰ N/m².
  5. So the answer is 5.16 × 10¹⁰ N/m².

Common slip: Using the uncorrected diameter, or using d instead of d² for the area.

Question 2

A uniform metre scale of mass 60 g (its weight acts at the 50 cm mark) is balanced horizontally on a knife-edge at the 62 cm mark. A 60 g mass hangs at the 15 cm mark and an unknown mass X hangs at the 90 cm mark. Find X.

  1. 88.5 g
  2. 75 g
  3. 126 g
  4. 101 g

Answer: C. 126 g

  1. Take moments about the knife-edge at 62 cm. Anticlockwise (left side): the hanging 60 g at 47 cm and the scale's own weight at 12 cm from the pivot.
  2. m(62−15) + M_s(62−50) = X(90−62).
  3. X = (60×47 + 60×12) / 28 = 126 g.
  4. So the answer is 126 g.

Common slip: Leaving out the scale's own weight, or measuring arms from the 50 cm mark.

Question 3

A vernier calliper has 1 main-scale division = 1 mm and 10 vernier divisions equal to 9 main-scale divisions. In a reading the vernier zero lies just beyond the 31th main-scale division (reading 31 mm) and the 6th vernier division coincides with a main-scale division. There is no zero error. What is the reading?

  1. 31.60 mm
  2. 32.20 mm
  3. 31.67 mm
  4. 37.00 mm

Answer: A. 31.60 mm

  1. LC = 1/10 = 0.1 mm.
  2. Reading = MSR + (coinciding VSD) × LC = 31 + 6×0.1
  3. = 31.60 mm.
  4. So the answer is 31.60 mm.

Common slip: Multiplying the coinciding division by a main-scale division instead of by the least count.

More Physics chapters

Start a free test